Welding & Assembly

Custom Sheet Metal Welding & Assembly

Joining formed sheet metal parts into finished assemblies, with welding and hardware requirements reviewed together as one project.

Diagram of a welded T-joint: a vertical sheet metal member joined to a base plate with fillet welds on both sides, the matching weld symbol from the drawing, and a welding torch at the joint 1/8 1/8 WELD SYMBOL VERTICAL MEMBER TORCH FILLET WELDS BASE PLATE

Custom Metal Welding

Welding turns individual sheet metal parts into rigid assemblies, such as frames, enclosures, brackets, and structures that cannot be formed from a single blank. Welds are made to the type, size, and locations specified on your drawing, including tack, stitch, and continuous welds.

Sheet metal assemblies are commonly joined by gas metal arc welding (GMAW, often called MIG) or gas tungsten arc welding (GTAW, often called TIG). The right process depends on material, thickness, joint design, and appearance requirements, and it is selected for each project during review.

If your project must meet a welding code or requires specific procedures or inspection, state the requirement in your request so it can be reviewed before quoting.

Stainless Steel Fabrication

Stainless steel calls for controlled heat input to limit distortion and discoloration, and for clean handling to protect its corrosion resistance. Tools and abrasives used on carbon steel should be kept separate from stainless work to prevent contamination. If your part has finish or post-weld cleaning requirements, note them on your drawing.

Aluminum Fabrication

Aluminum conducts heat quickly and forms an oxide layer that must be removed before welding, so it is handled differently from steel. Alloy choice also matters: 5052 forms well in the press brake, while 6061-T6 is stronger but more prone to cracking in tight bends. Specify the alloy and temper on your drawing so the full fabrication route can be planned.

Sheet Metal Assemblies

Many products are built from several formed parts joined together. Assemblies can combine welded joints, self-clinching hardware, and mechanical fasteners. Provide an assembly drawing and bill of materials so every component and fastener is accounted for in the quotation, and note whether you need complete assemblies or individual parts.

Hardware Installation

Self-clinching fasteners add strong, permanent threads to sheet metal that is too thin to tap. Nuts, studs, and standoffs are pressed into properly sized holes; the fastener's knurled displacer pushes sheet material into an undercut on the shank, locking it in place.

Cross-section of a self-clinching nut installed in sheet metal: a press pushes the nut into a punched or drilled hole, the knurled displacer forces sheet material into the undercut on the shank, and the nut becomes a permanent threaded insert PRESS SELF-CLINCHING NUT THREADED BORE KNURLED DISPLACER ANVIL METAL FLOWS INTO UNDERCUT SHEET METAL

PEM® Fastener Insertion

PEM® self-clinching fasteners are widely specified in electronics enclosures, chassis, and equipment panels. Specify fastener part numbers on your drawing. Mounting-hole sizes and minimum sheet thickness follow the fastener manufacturer's published specifications, and distances from edges and bends are checked during drawing review.

PEM® is a registered trademark of PennEngineering. IronTrail Precision is not affiliated with PennEngineering.

What to Include for Welded Assemblies

  • Assembly drawing with weld symbols showing weld type, size, length, and location
  • Material grade and thickness for every component, including dissimilar materials
  • Any welding code, procedure, or inspection requirement that applies
  • Cosmetic surfaces, weld finishing, and post-weld cleaning requirements
  • Fastener part numbers and locations for installed hardware
  • A bill of materials, and whether you need complete assemblies or individual parts

Manufacturing services are coordinated based on project specifications, material requirements, and production needs.

Welding and Assembly Questions

Can welding meet a specific code or standard?

If your project requires welding to a specific code (for example, AWS D1.1 or D1.3), qualified procedures, or inspection documentation, state the requirement in your request. Requirements are reviewed before quoting, and you will know before production whether they can be met.

Which fasteners can be installed?

Self-clinching nuts, studs, and standoffs are the most common. Include fastener part numbers on your drawing; mounting-hole sizes and sheet thickness requirements are checked during drawing review.

Do you supply complete assemblies or individual parts?

Either. Note in your request whether you need finished assemblies, kits of individual parts, or a combination, and include the bill of materials.

Have an Assembly to Quote?

Send your drawings and requirements. Accepted formats: PDF · DXF · DWG · STEP · STP.