Precision Metal Cutting from Your CAD Files
Fiber laser cutting produces flat parts and blanks directly from your DXF, DWG, or STEP files, without hard tooling. That makes custom laser cutting practical for a single prototype and efficient for repeat production.
Sheet metal laser cutting is usually the first operation for a part, before CNC press brake bending, welding, and assembly. Cutting and forming requirements are reviewed together so that bend reliefs, hole locations, and flat-pattern dimensions support the finished part.
How Fiber Laser Cutting Works
A fiber laser generates its beam inside an optical fiber doped with a rare-earth element and delivers it to the cutting head through a fiber-optic cable. A lens in the head focuses the beam to a very small spot at or near the sheet surface, where it melts the metal. An assist gas, typically nitrogen, oxygen, or compressed air, flows through the nozzle and clears molten material from the cut while the CNC moves the head along the programmed path.
The result is a narrow cut, called the kerf, with accurate geometry and a clean edge. Because the beam does not touch the part, thin sheet is cut without the mechanical forces of punching or shearing.
Advantages of Fiber Laser Cutting
No hard tooling
Parts are cut directly from CAD data, so prototypes and design changes do not require new punches or dies.
Accuracy and repeatability
CNC-controlled motion and a narrow kerf produce consistent profiles and hole positions from part to part.
Complex geometry
Intricate contours, small holes, slots, and tab-and-slot features are cut in a single setup.
Clean edges
A tightly focused beam and assist gas produce clean edges with a small heat-affected zone, reducing secondary cleanup.
Efficient material use
Parts are nested together on each sheet to reduce scrap and material cost.
Ready for forming
Bend reliefs and features are built into the flat pattern, so laser-cut blanks move directly to the press brake.
Common Laser-Cut Parts
- Flat blanks for formed parts
- Brackets, gussets, and clips
- Panels and faceplates with cutouts
- Mounting plates and base plates
- Tab-and-slot parts for welded assemblies
- Covers, shields, and guards
Materials and Requirements
These sheet materials are the most commonly specified for laser-cut parts:
- Aluminum. Enclosures, chassis, covers, panels, brackets.
- Stainless Steel. Equipment covers, frames, brackets, sanitary-style panels.
- Carbon Steel. Brackets, frames, guards, structural and mounting parts.
Include the material grade, thickness, and quantity in your request, and mark critical dimensions and tolerances on your PDF drawing. Feasibility is reviewed for each project before quoting, and anything that needs clarification is raised before production.
Preparing Files for Laser Cutting
- Send DXF or DWG flat patterns at 1:1 scale, and state the units (inches or millimeters).
- Use closed contours with no duplicate or overlapping lines.
- Remove title blocks, dimensions, and notes from cutting files, or place them on a separate layer.
- For formed parts, include a 3D STEP model so the flat pattern can be checked against the formed geometry.
- Include a PDF drawing for tolerances, critical dimensions, and finish requirements.
- Note the material, thickness, quantity, and any grain-direction or cosmetic-side requirements.
Laser Cutting Questions
What file formats do you accept?
PDF, DXF, DWG, and STEP/STP. A 3D STEP model together with a dimensioned PDF drawing gives the most complete picture of your part.
What material thickness can you cut?
Include the material, grade, and thickness in your request. Feasibility for your specific part is reviewed before quoting, and any requirement that cannot be supported is raised before you receive a quotation.
Is laser cutting practical for prototypes?
Yes. Laser cutting requires no hard tooling, so single prototypes and small quantities are practical, and the same cutting data can be reused for production.
Can laser-cut parts also be bent, welded, or fitted with hardware?
Laser cutting is usually the first step for parts that are later formed, welded, or fitted with hardware. Describe every operation your part needs in your request so the full route can be quoted together. See CNC press brake bending and welding and assembly.
Do you quote laser cutting for customers outside Texas?
Yes. Customers anywhere in the United States can request a quote. Include your delivery location, and shipping arrangements are confirmed with your quotation. See service areas.
